Stylish and comfortable paths in the garden with your own hands

Paths are an integral part of the garden. Not only the appearance of the estate, but also the convenience of movement throughout the site depends on how they are laid and combined with each other. Therefore, the arrangement of paths and paths is the main stage in the design of the landscape gardening area.

How to plan a track layout

It is best to plan the layout of the tracks during the planning and zoning of the site. This will make it possible to provide approaches to all necessary buildings and zones.

If necessary, in the future, after the appearance of a new building, or a change in layout, you can always correct the route or change direction. The marking should be carried out taking into account all routes, so that a convenient passage is provided to each important element of the garden.

To begin with, you should draw up a site plan and think over all possible objects, including both communication and architectural or design ones. After marking all the routes, it is necessary to determine the width of the track, taking into account what exactly it will be used for.

• The main path - going from the gate to the house and to the most visited places, for example, a gazebo or a playground, should be 0.9-1.5 m wide. This is necessary not only for the possibility of the passage of two people, but also helps to highlight it visually.
• Paths of secondary importance (to utility rooms, a bathhouse, outbuildings, recreation areas) - from 60 to 90 cm.
• For paths going deep into the garden or vegetable garden, a width of 35-50 cm is suitable.

The exact width of the tracks is not given, as it depends on the size of the site and on personal preferences. However, for a large section, it is recommended that each branch of the road be twice as narrow as the previous one. For example, the main one is 1.2 m, then the secondary one is 60 cm, and the garden one is 30-35.

It is equally important that the paths fit perfectly into the overall style of the site. For a landscape-style garden, serpentine paths with gentle turns are best suited. Their width is made the same, and on the steps to the sites or buildings they are gradually expanded.

Landscape style garden design or English garden. Also called Nature Style or Natural Garden, contains irregular and uneven shapes, mixed plantings and planting areas.

In a garden of regular construction, paths are laid out exclusively in a straight line, so that they are parallel and perpendicular to each other, fences and walls of the house. A ray scheme or symmetry is also suitable for this style.

For the reader's reference

Landscape style A regular garden is the exact opposite of a landscape style. May also be called French Park, Geometric Garden, Garden of Regular or geometric construction. Differs in the correct equal forms and symmetry of execution. It is considered the most strict and light style in landscape design.

Materials for paving paths in the garden

When choosing which paths to make in the garden with your own hands, it is important to consider the basic requirements: strength, safety and affordability. What is the best way to make them? And how to determine the required amount of materials?

The most popular are:

• paving slabs;
• a natural stone;
• granite chips;
• paving stones;
• pebbles;
• stamped concrete;
• concrete plates;
• bars and saw cuts of trees;
• terrace board.

Choosing building materials for paving should be based on the purpose of the paths and sites. On the main routes, especially if the house is permanently occupied, a continuous hard surface of concrete, tile or stone is laid. For backfilling the central paths, as well as for paving routes of secondary importance, brick chips, gravel or pebbles are used.

The central paths and porches are paved with the same type of material to give the entire space a stylistic unity. If the area of ​​​​the site is large, you can combine several types of coatings, but no more than 2-3. For laying serpentine paths, it is better to choose elements of medium size - paving stones, clinker, paving slabs.

Before laying the coating, it is necessary to make the base of the track. To do this, they dig a trench, having previously calculated its depth according to the formula: the height of the base layer plus the height of the surface coating. Usually, a 30 cm layer of fine-grained sand and gravel, or crushed stone, is used to create the base. In this case, the sand component should not be more than 50%. The base is laid out in 4-5, approximately equal layers, each one is carefully spilled with water for precipitation and compacted.

Determination of the amount of facing material

In order to determine how much material is required to paving the surface layer of the path, it is necessary to determine the length and width of the future garden path, and then, by multiplying, calculate its total area. For example, for the construction of a path measuring 1.2 by 7 m, about 63 tons of decorative gravel will be required.

This calculation is based on the following data:

• According to the data from the example, we obtain the coverage area: 1.2 * 7 \u003d 8.4 square meters;
• For a stable coating, according to the norms, it is customary to take a height of 5 cm;
• The coverage volume is equal to the coverage area multiplied by the height: 8.4 * 5 = 42 cubic meters;
• The bulk weight of decorative crushed stone can be obtained from the manufacturer, on average it is one and a half tons per cubic meter;
• Based on these data, we expect that our track will need 63 tons (42 * 1.5).

You can calculate the amount of sand and gravel for the base approximately, according to the same principle. The bulk weight of fine-grained sand is 1.72-1.8 tons per cubic meter, and fine-grained crushed stone of the M700-M800 brand is 1.41 tons.

Paths in the garden of stone, tiles and bricks: design options

Slab is the most popular material for organizing tracks. Firstly, it is easy to lay out, secondly, it is durable and wear-resistant, and thirdly, it is quite easy to care for it.

The modern building materials market allows you to choose paving slabs for every taste - all kinds of shapes, colors and textures. In order to decorate a large area - a parking lot or a platform near the porch, it is enough to combine 2-3 options by organizing inserts on the main canvas with a diagonal or patterned placement of tiles.

A mosaic or abstract patterns of multi-colored tiles of various sizes will look very unusual and festive. For connoisseurs of natural style, tiles with gaps will be an excellent solution, which, after laying, can be sown with grass or covered with soil.

Do-it-yourself garden paths made of natural stone

Natural materials - basalt, granite, limestone, sandstone allow you to realize the most daring fantasies. With their help, you can make a path of any purpose a real artistic element of the garden. The main advantage of such a coating is harmony and strength. It will not be difficult to pave paths from natural stone, even for a non-professional.

For the construction of walking paths, it is most rational to use full-sawn paving stones - stone blocks that resemble a parallelepiped in shape. And access roads should be paved with chipped paving stones. Irregular flagstone paving, 4 cm thick, looks no less beautiful. It must be selected according to the shape, and laid on a bed of compacted sand or on a sand-cement mixture.

To save money

To save money, you can combine paving slabs, filling the main part of the paving with it, and make stone patterns in the center. For this purpose, a stone of any size left over from construction, boulders of an unusual shape, pebbles and shells brought from a trip are suitable. Brick chips, pieces of marble, granite, and even wooden saw cuts are also useful.

Walking paths in the garden, photo of original coatings using wood

Wood is not the most durable material, but wooden paths look very aesthetically pleasing and original. To ensure that the coating lasts as long as possible, it is treated with special impregnations before laying that protect against moisture and fungi: Drevotex-Anti-mold, Dali, Woodmaster Prof Biosept, Ecodom Bioprof. Such paths are installed only on elevated places where there is no possibility of waterlogging of the soil and stagnant water.

Walking paths leading into the distance of the garden are made of wooden saw cuts with a diameter of 20 cm or a rectangular beam 20x15 cm. The finished bars are laid out on a pillow of sand, covered with gravel on top. The saw cuts are driven into compacted wet sand, as close as possible to each other.

The most durable material for garden paths

More durable and durable paths made of decking boards. It is made of wood or wood-polymer material that is not subject to the damaging effects of weather conditions. Mount the coating on logs laid on a leveled surface. Fasten the boards to each other with screws or clips.

Logs are selected based on the selected terrace board. If wood-polymer materials are used, the logs should also be made of composite materials, since the service life of the parts of the structure must match. The surface under the logs can be made of various materials: paving stones, crushed stone and sand, sandstone or concrete. The main condition is a prepared flat surface, with a slight slope (1.5-2%) from the house for water flow.

Logs are laid at a distance of 40-50 cm, and in places of increased load 20-30 cm. Also, they should not be laid close to curbs and walls, the recommended distance is more than 20 mm. After that, the deck board is fixed. If completely natural materials are used, mandatory treatment with special oils that prevent decay is necessary.

Outcome

A beautifully laid out central path or an originally decorated winding path leading from home to your favorite vacation spot, pond or garden can not only emphasize the merits of plant compositions, but also become a spectacular garden decoration. Using the advice of our experts, you will make beautiful and comfortable paths in the garden with your own hands.

Increasingly, the dacha is becoming a place of rest for family and friends. The plots are equipped with houses and outbuildings, recreation areas and flower beds. A place is also allocated for the garden, which acquires decorative qualities. All objects are connected by a network of communications - paths. They allow you to avoid dirt, create convenience for agricultural work, walks in the fresh air and are elements of a single landscape design of the backyard area. Let's get acquainted with the basic techniques of beautiful and competent arrangement of walking paths for summer cottages.

What are they for?

The tracks are different functional purpose. Depending on this, certain materials are used, the width and laying technology depend on the purpose of laying the path. There are several basic functions of communications in the country.

Entrance from the gate to the porch of the house

This is the front area of ​​a private or country house, it is used most often. Wear-resistant, with good decorative qualities, material is appropriate here, which should be combined with the style of the main buildings, copy the material of the basement, have sufficient width (from 80 cm to 1.5 m) to calmly miss each other when meeting two people or ride a bicycle to the house. Requires a flat surface.

When choosing a material for the main entrance path, paving slabs, concrete slabs with decorative design, and natural stone are preferred.

Connecting house and outbuildings

For this variety, the coating material is chosen strong, durable. Paths are best done straight (for example, for the convenience of moving with a wheelbarrow during gardening). Width varies from 80 cm to 1 meter. The surface of these paths should be smooth, non-slip, comfortable for use in rainy or snowy weather.

In addition to the above materials, more affordable concrete pouring into the formwork can be used here. For better wear resistance, it is reinforced with a metal mesh. Well proven artificial stone. It is much cheaper, is not inferior in performance to natural materials, has a mass of colors and imitates different structures.

walking

I make walking paths from lightweight materials: wood, sandstone with intervals of ground cover plants or sand, mosaic concrete slabs. These paths can be covered with pebbles, sand, tree bark. The width of the tracks varies in distance from the main communications and is calculated based on the size of the entire area. If possible, it is necessary to provide a width of 1 meter for walking together. To create a flair of mystery and romance in special corners of the garden, a width of a standard tile size of 35-50 cm is allowed. Any curved shape is welcome here, emphasizing the soil relief or garden zoning.

Natural materials in the landscape look natural and harmonious.

Paths between beds

Their function is to limit the sticking of dirt during gardening, to organize the space of vegetable plantings. These tracks are made with a size of 50 cm, the material of manufacture can be very diverse (from rubber tires to plank coverings on logs). Under these paths, it is not at all necessary to make a sand and gravel pillow: most often they are simply laid on the ground. When redeveloping the beds, these paths are easy to move to a new location.

When arranging stationary high beds, the paths are covered with rubble laid on black acrylic insulating material. This material isolates them from the germination of weeds, while moisture passes freely deep into the soil. Small gravel paths look aesthetically pleasing and last a long time. Paths in the country house that are different in functionality can be designed in the same style using the same material, changing only the width and shape of the paths. It all depends on the preferences of the owners, the size of the plot and the price segment of landscape work.

Location selection

An important stage in the improvement of the suburban area is the road and footpath network around the cottage and the surrounding area. At the first stage of planning, future paths are traced. There are two approaches to tracing: if the development exists or the site is just being developed. In the already existing buildings, they are guided by the trodden dirt paths between the objects. These paths are taken as a basis, applied to the site plan, given a technological size and the desired curvature, or slightly straightened for ease of use, while not violating the vector of the path itself.

To develop a new site, the necessary and desirable paths are applied to the plan. Better to do two or three options. According to these plans, they make orientation on the terrain, pass along these routes several times, evaluate the convenience of movement. They make changes depending on the relief or taking into account economic needs and the location of communications. In both cases, there are common factors that affect tracing.

The first to plan the necessary economic paths:

• from the gate to the porch of the house;
• from home to outbuildings;
• to the garden area.

These communications are subject to the same requirements, the main of which are:

• wear resistance;
• sufficient width for the passage of small garden equipment;
• ease of cleaning from debris or snow;
• non-slip coating;
• no sharp bends.

Additional paths are needed to connect with a recreation area or access to remote corners of a summer cottage.

The load on them is not as large as in the first case. Decorative and useful qualities do not require straightness or a particularly flat surface. Paths can be made from improvised materials, use the inclusion of natural elements. Often they are given a deliberate curvature to lengthen the route or inspect certain landscape compositions. The width can also vary.

After tracing and determining the width of the transitions, the terrain is studied. In order to protect against the formation of puddles on the surface, a slope must be observed. The soil in some areas will have to be poured. In others - choose to align the top layer. If the relief of the site is textured, has large elevation differences, it may be necessary to install stairs or sample a large amount of soil with retaining walls to prevent soil from falling onto the path. In some cases, it is necessary to change the location of the track around relief recesses or ledges in order to avoid a large amount of land work.

Next, take into account the drainage device. For continuous paths on a cement base, a transverse slope method is used from the middle to the edges to drain water. The middle is made somewhat higher, the finishing material is laid along the arc to the side faces. The slope must be at least 15 degrees. Paths with more sparse laying of finishing material on the ground, sand or gravel have natural drainage. When constructing a curb, it is necessary to lay special storm systems under the road surface.

The next stage of planning is to create a decorative effect. The communication network is not only of practical importance, but is also an element of landscaping the landscape design of a personal plot.

Simple concrete paths are practical enough, but a network of dull gray straight lines is unlikely to please the eye. They should be given some curvature, for example, a sharp turn over the hill can open a beautiful flower bed.

Pathways can be a means of visually changing the parameters of a site. A narrow elongated section will look wider with a sinusoid path across the section. In a short section, it is better to place the coating material along the track web. This will visually lengthen the area. The transverse layout of the material will visually reduce the distance.

The color scheme of the finishing material is selected at the planning stage. Here you need to rely on the basic colors of the environment. A house surrounded by dark green coniferous trees will require gray, dark stone paths or finishes the color of withered needles. The paving pattern plays an important role in the overall perception of the landscape. For example, cottages decorated in a rural style can be decorated with brick or homemade mosaic paths. Children will love the soft rubber tracks made of tires.

Planning ends with the preparation of estimates for the purchase of materials. The length of the canvas is calculated, multiplied by the width and the required amount of finishing material is obtained. It is worth considering land works: will they be carried out independently or will it be necessary to involve equipment and specialists. For cement-based paths, the presence of a sand cushion of 10-15 cm, layers of crushed stone, a cement-sand mixture in a ratio of 1: 6 (for laying slabs) are taken into account. If the tracks are made of different materials, estimates are made separately for different types of coverage. This is justified, as resource savings can be achieved by using a simplified approach to arranging secondary paths. To do this, consider the types of garden paths.

Types of garden paths

Garden paths are divided into two types: hard and soft.

Solid

Hard coatings are made of bricks, concrete tiles, clinker stone, limestone, paving stones. Such coatings are used in parking lots for cars, in the entrance area, on the main alleys of the site, between summer cottages.

A hard surface is chosen for paving recreation areas and some paths.

A special foundation is being prepared for them.

The soil is selected to a depth of 25 cm, the bottom of the trench is tamped manually or mechanically by means of a vibrotamper. For the manual method, a special rammer is made from a log with a nailed transverse bar instead of handles. The bottom of the trench is lined with geotextiles to isolate weeds. A layer of sand is poured (5 cm), after tamping, a layer of crushed stone (from 5 to 10 cm) is laid on it, rammed and covered with sand.

After that, they spill it with water so that the sand fills the voids between the pebbles well. After drying, it is again sprinkled with sand with a layer of 5 cm, followed by a layer of cement-sand mixture (5 cm). Finishing material (natural stone, brick or slabs) is laid on this layer. Rammed and covered with cement mixture. Spilled with water and again covered with cement mixture until the desired leveling level is reached.

Soft

Soft coating on the paths is made of crushed stone, sand, wood, bark, rubber, marble chips, pebbles. Such paths are walking, although they are also used to care for the garden. Grass and rubber are optimal for playgrounds. For soft finishing material, it is not necessary to prepare a complex trench before laying. Here it is enough to take out the soil to a depth of 10 cm, tamp it down, cover the geotextile from weeds, pour 5 cm of sand and lay the finishing material.

From paving slabs

Paving slab paths have a universal purpose. Laid on a cement-sand mixture, they will serve excellently on the main driveway due to their high performance.

Tiles placed at some distance from each other with gaps of grass cushion will create a clean, dry path in tune with the natural landscape.

Pedestrian paths in the country can be beautifully combined from different materials, most importantly, it is necessary to take into account the general style of the design of the site.

Styles

The same finishing material in a certain context can be a participant in retro styles and the most modern trends in landscape design at the same time. If you want to create a garden in a certain style, you should adhere to the following rules.

• For site clearance mediterranean style choose pebbles, tiles and sand. Country is perfectly combined with natural wood flooring. Forest areas are landscaped with paths made of stone, cobblestones and tree cuts. The use of crushed bark for backfilling paths looks interesting.
• Modern especially loves floral decor and rounded smooth lines. Eco-style prefers paths made of sand and stones, covered with fine gravel (without curbs, almost invisible in the landscape).
• wood and stone- traditional materials used for centuries for the equipment of paths. Today they receive special attention.

Country

Eco style

A striking example of a combination of a variety of materials is high-tech industrial style in landscape design. It combines glass and metal, concrete and plastic, water and stone. These materials can be arranged randomly and symmetrically. The main thing is the presence of a clear geometric pattern. The tracks are strictly straight, the turns have a strict pattern. The coating avoids texture, the color scheme is restrained and monochrome. The most popular coatings are made of concrete and marble backfill with inclusions of glass elements edged with metal. The aquatic environment is presented in an original way in this technological design.

The design of the paths has the same bright uniqueness. Japanese style. If the high-tech style sharply delimits the natural environment and the human habitat, the Japanese style includes a person in the natural landscape. Finishing materials here are natural stone and wood, plants and streams. The paths are combined with bridges and seating areas in a classic Japanese style.

Great importance is attached to natural stone. The stone has a deep philosophical meaning and is a symbol of original ethnic design. The entire garden or a separate section of it is decorated with appropriate plants. The paths have smooth bends, the surface is decorated using pebbles, crushed stone and flat boulders.

The width can be arbitrary: from very narrow paths for contemplative lonely walks to wide dry rivers. Smooth and smooth paths are combined with compliant rapids boulders.

From the same materials, you can create completely different style solutions for decorating a summer cottage.

Let us examine in more detail what materials can be used in the construction of suburban communications.

materials

For the manufacture of tracks using different materials.

Flagstone

Traditional options for the design of paths in the country are natural and artificial stone flagstone. The stone has a maximum wear resistance coefficient, it is one of the most durable materials. It is not exposed to seasonal temperature changes, has the necessary roughness, which ensures the absence of slip. Has a huge range of colors. It is better to choose the color according to the color of the house or basement: this will unite the house and the garden compositionally.

Laying flagstone does not require special skills; this work can be done without the involvement of special workers. They arrange the preparation of the soil for hard coating, the stone is laid with a small gap (like a mosaic).

The stone pavement does not require a curb; any bend in the trajectory can be made.

The width of the path is easy to smoothly change throughout, which gives naturalness to the whole look of the garden and yard.

There are several types of natural stone: slate, quartzite, granite, sandstone, shungite. The stone with gaps filled with lawn grass creates a warm and comfortable transition through the area. The disadvantages of this paving include the high cost of the material. For a budget option, it is better to use paving slabs.

paving slabs

Paving slabs are as durable as stone. There are concrete and ceramic tiles. It can have a pattern, then it is laid out in the form of an ornament. This is a very colorful coating with excellent performance. Manufacturers offer tiles with a surface color or completely colored (in the first case, the top layer may wear off after a few years).

For parking and the front alley, vibrocast tiles are used: they are more resistant to loads, vibropressed tiles are more appropriate for paths. Tiles are produced in the form of bricks, rhombuses, coils of different colors. Smooth edges allow you to install a border that can be matched to the tone of the main pattern. Paving is carried out using hard coating technology with a wide variety of patterns.

Clinker brick

Durable hard coating is clinker brick. This material is not afraid of moisture, has an interesting range of colors and is designed specifically for tracks. It can be covered with a cement-sand mixture. Another way is to fill the top layer with soil and sow grass seeds, however, caring for this cover is more laborious (weeds will have to be removed, and grass should be sown in places of abrasion).

From a brick, you can lay out various schemes, as well as from a parquet block.

decking

For road surfaces, a special garden wooden parquet - decking has been created. For its manufacture, a particularly hard wood or plastic is used that imitates different kinds parquet wood layout. Decking is produced in the form of plates or individual planks, which are laid out on a prepared base in a certain pattern. The sections have dimensions of 35 x 50 cm or 50 x 50 cm, due to special fasteners they are interconnected, they are laid on special supports. Such a connection allows you to model the track according to the relief of the site.

You can assemble the parquet flooring yourself. Using a deck board to decorate paths made of natural or polymeric materials will not hit the budget. Decking requires the preparation of a base of concrete screed or sand and gravel pad. Garden parquet requires thorough care, it must be protected from moisture, regularly impregnated with special compounds. Particularly valuable species of wood need to be dismantled for the winter.

Concrete

Hard pavement can be made independently from reinforced concrete. Prepare a sand and gravel pillow. A metal mesh is laid on it. Formwork is installed and poured with a cement-sand mixture. The top layer can be decorated with pieces of old ceramic tiles, fragments of dishes. Get a kind of colorful mosaic.

The original pattern can be laid out from multi-colored caps from plastic bottles in cement that has not yet hardened. True, you will have to make an effort to collect them. However, the result will be bright and exclusive. If a river flows nearby, the surface of the concrete path can be laid out with pebbles or shells.

A variety of patterns and natural colors of the path will decorate the summer cottage.

Modules

With a lack of finishing material, it is worth casting individual concrete slabs. It is worth preparing a pillow under the base in size, making a formwork in the ground and pouring it with concrete, the top will remain to be decorated according to your taste and the availability of material. The combination of materials gives an excellent effect: this is how the monotony of one finishing material is broken. At the same time, high performance is maintained.

The advantages of modular tracks are in a variety of shapes., the possibility of decorating them with improvised materials, giving color with the help of color. Modular tracks are easy to repair by replacing modules. They can be made gradually, lengthening the track as needed. Simple rectangular modules look stylish against the background of the lawn.

Plastic

Plastic garden paths have become a new offer on the market of finishing materials. They immediately gained popularity with ease of installation, ease of maintenance and low cost. Colorful plastic covers are sold in rolls or modules, which are assembled like a designer. This type of coating is not so durable, but it does a good job of protecting against dirt. Rolling tracks in your summer cottage can be laid even by a pensioner.

Plastic modules are indispensable in the garden or playground, they are easy to move to the right place or put away for the winter.

gravel and crushed stone

Soft paths on the plot are covered with gravel and rubble. For the foundation, they dig a shallow trench, tamp the bottom, lay geotextiles and fill in crushed stone or gravel. It is better to install curbs here so that small pebbles do not spread throughout the territory. This type of path looks especially impressive when using gravel of different colors.

Rubber

Budget and comfortable tracks are made of rubber mats. Rectangles of thick rubber are laid in the right place - and the path is ready. It does not slip, it is pleasant to walk on it barefoot, as it is warm even in cool weather, light and durable, it will last several seasons. Often in this case, rubber tires from old wheels are used.

To do this, the side parts are cut off from the tire, the resulting ring is cut and straightened in the form of a track. On the one hand it is smooth, on the other it has a tire relief. You can use either side. Aesthetic qualities leave much to be desired, but such paths perform the practical function of protecting against dirt well.

Wood

Traditional wooden paths in the country house are environmentally friendly, inexpensive and beautiful. You can use the remains of boards or wooden pallets from the transport of building materials. The pallets are of sufficient width, the blocks consist of identical processed boards. They can be laid out along the track, but the service life will be short-lived, some boards may break and create a risk of injury. It is better to dismantle the pallets, prepare a trench from crushed stone or concrete, lay boards on top of the logs, fix them with self-tapping screws and treat them with special anti-rotting agents.

The paths from the saw cuts of the tree look beautiful. Saw hemp 10-15 cm high, prepare a trench, fill up a sand cushion. Hemp impregnated with an anti-corrosion compound is installed in a trench, the gaps are covered with sand or small gravel. Such paths are appropriate in coniferous landscape compositions.

bottles

A path made of bottles will become a peculiar solution for garden communications. The principle of the device is similar to the previous version. Only instead of stumps, bottles filled with sand are installed. Glare of light reflected from the glass creates a pleasant sheen.

The trench for the path can be laid out with bricks left over from construction. It is worth remembering that red brick is susceptible to moisture. After a few years, it will have to be replaced with a new one. Preparation for laying is done, as for a hard surface.

Paved paths made of paving stones or cobblestones are the most preferred options for creating a hard pavement. These materials are durable, wear-resistant, their decorative qualities make it possible to use paving in the front area.

Masonry schemes

There are many options for laying tracks. Their creation is a fascinating process.

At the same time, for the best result, it makes sense to refer to the main schemes that professionals adhere to:

• Linear-angular scheme. The bars are laid end to end to the edge of the longitudinal side. It turns out a "herringbone" at an angle of 90 or 45 degrees.
• Linear with shift. Classical form: the bars are laid in a row, the second row is set with a seam in the middle of the long side of the first row, while the outer bars are shortened by half.

Linear-angle scheme

Linear with offset

• Multi-colored tiles are laid in a checkerboard pattern.
• "Braid" is obtained as a result of alternating longitudinal and transverse tiles.
• The end arrangement of the bars is used to mark the boundaries of the track or pattern.

When choosing a laying method, you need to know that the transverse arrangement of tiles visually shortens the length of the track (and vice versa). A herringbone at a 45-degree angle visually compresses the space, a herringbone at a 90-degree angle expands the canvas of the track. The most simple in laying the herringbone and braided patterns. They are convenient to use when working with the correct form of bricks or rectangular tiles.

The stone can be laid "seam to seam" or "running apart". In the first case, the edges of the ends are combined, in the second they are shifted by a certain amount. Laying "in a run" gives an interesting picture of movement in a wave or diagonally. Apply the alternation of the longitudinal and end parts of the stone. This technique creates "Gothic", "Dutch" masonry, "well" or "cross" masonry. The most difficult is the "radial" masonry. Its implementation is best left to specialists.

markup

The initial stage of arranging the tracks is the marking of the route. To do this, the contours of the future path are poured with chalk or sand along the entire length and the desired width. The width is set slightly larger than the size of the track itself for the installation of formwork, curbing or installation of a drainage system. Once again they study the track, evaluating the convenience and sufficiency of the width of the track. It is important to take into account the view that opens from the path, think about where the water supply and electric cable will pass.

To do this, they pass along the future route several times, visually representing the size of adult plants along the path, so that they, when growing, do not interfere with traffic, and the roots do not destroy the roadway. From large trees, the path should run at a distance of at least 2 meters. If there are no green spaces yet (or they have not grown yet), sand outlines the contour of the crown in adulthood. Dimensions can be found in plant guides.

It can be difficult to imagine a particular plant in the future. Then use the following method. Large stones, boxes, or a stake are driven into the landing sites (this will help visualization). After the approval of the route, the paths begin to lay out the finishing material.

How to post?

To save material resources, many landowners equip a pedestrian network in the country with their own hands. This process consists of several stages.

Digging a trench for the bed of the track

By backfilling, choose the soil to the desired depth:

• for hard coatings at 25-30 cm;
• for dumping by 10 cm.

The bottom of the trench is leveled and checked according to the building level so that there are no holes and bulges. It is necessary to monitor the general slope of the path for draining water (5 degrees). If this slope cannot be provided, the slopes of the finishing material web itself to the sides (5 to 15 degrees) are provided. The bottom of the trench is tamped with a log with a nailed plank or a mechanical rammer.

Foundation preparation

Sand is poured at the bottom with a layer of 5 cm for hard and soft coatings. They ram, check the level of the horizon and the slope. Next, rubble is poured with a layer thickness of 5 - 10 cm. You can combine these two components and immediately fill the bottom with a sand and gravel mixture. Next comes another layer of sand 5 cm thick. Everything needs to be well shed with water and left for several days to dry. Finally, a final level check is carried out and sand is added in the right places - and the foundation is ready.

Laying finishing material

On the compacted top layer of sand, a stone, tile or brick is laid out according to the chosen pattern. With a lack of experience, it is better to first lay out a small part of the pattern on the ground, and then lay it out on the base. Flagstone, cobblestones, paving slabs can be laid on a cement-sand mixture or concrete. Brick and paving stones - on the sand.

The technology of laying out on concrete is similar to tiling indoors. In the second case, sand and a sand-cement mixture are poured onto the base in a small layer. The coating material is tightly laid on them and rammed, regularly adding sand or a mixture from above, sweeping with a brush, spilling water, and pouring sand again until the joints are completely filled.

If it is necessary to install a curb, it is installed before the start of work on the construction of the base under the track bed. For dump paths, the technology is simpler. Here you can use the option of laying on a concrete screed with a curb or on a sand and gravel mixture. For narrow garden walking paths, a simplified version of the construction of paths made of brick, gravel, sand, concrete or paving slabs is used.

To print

10.03.2015 | 10242

Garden paths will take on a completely different look if they are decorated with flower borders.

Gone are the days when paths in the garden were needed only in order not to get your shoes dirty. Now they are an element of landscape design. And it does not matter at all what you grow on your site. Even if the entire area is reserved for a garden, you simply have to plant ornamental plants along the edges of the beds.

Path design options

1. Classic tracks, which have a length much greater than the width, usually make out discounts or mixborders. The former, as a rule, consist of dense plantings of annual flowers, and the latter are a multi-level flower bed.

2. If your path has intermittent coverage and consists of separate segments, you can land creeping between them. perennials with bright and long flowering.

3. An interesting solution for decorating a garden path can be decorative houseplants planted in pots, ceramic bowls or wicker containers. The most suitable for this are begonia , coleus and zonal pelargonium .

4. To frame your paths decorative throughout the spring-autumn period, land perennial plants with different flowering periods.

5. If your yard has paths that are close to the patio, or one that hardly anyone walks on, use bryophytes to decorate them. Arends' saxifrage and army as well as multi-colored "pillows" subulate phlox .

6. Unusual foliage and colorful flowering can be safely combined with decorative mulch. It can be painted shavings, bark or gravel. Some designers even use glass balls. Depending on your taste, make the composition monophonic or contrasting.

The choice of plants for the design of paths

It is necessary to plant along the paths such plants that either bloom for a very long time or have decorative foliage. Low curbs look great boxwood, lavender, small petal, alpine aster, stakhis .

Can be used to decorate the front edge of flower beds daffodils, tulips, hyacinths and other bulbs that bloom in early spring. When they shed their leaves and retire, it will be possible to plant seedlings of one-year-olds, such as petunia, viola, ageratum, verbena, lobelia, salvia, Snapdragon, marigolds, cineraria, cochia etc.

In order not only to receive aesthetic pleasure from the flower garden along the path, but also to enjoy a pleasant aroma, plant mignonette, peonies, alyssum, iberis, catnip, night violet , levkoy or miniature bushes roses .

Spicy low-growing plants can be grown even between individual segments of the path, in the resulting cracks in the concrete pavement. Drop off in places like this thyme, thyme, catnip, oregano . If suddenly you accidentally step on them, the air will be filled with a pleasant aroma. For such a design, any ground cover perennials that are resistant to trampling are suitable.

For a shady garden, you can use hoof, primrose, daisy, geranium, tenacious, periwinkle or undersized host.

To print

Read also

Read today

Care Tips Learn all about collecting and storing flower seeds

Growing flowers from your own seeds is a simple and fun process that allows you to get a large number of your favorite...

From how the paths will be decorated on a suburban area, its entire design largely depends. Even in such conditions, when it is not possible to perform time-consuming and expensive work, you can choose more affordable options that have been developed and already tested by craftsmen.

Do-it-yourself paths in the country can be made from a variety of materials by choosing the appropriate option from the ones below. For example, ordinary bricks or round logs sawn from logs, round, medium-sized pebbles or ordinary corks from plastic bottles are perfect for these purposes. There are also removable options for tracks that can be laid exclusively for the summer period. By the way, such tracks can also not only be purchased ready-made, but also made independently.

In any case, before laying any garden paths, it is necessary to carry out preparatory work.

First of all, you need to schematically place a house, outbuildings on the plan, connecting them together and paving the way to the entrance gate - these will be the main paths, which you cannot do without in any case.

Then, you need to plan paths leading from the house to various areas of the site, for example, to the gazebo, pool, playground or zone.

If there is a need, then, having brought the path to the garden or garden, it is worth branching it in such a way that it is convenient to get to every corner of the site in any weather, since the lack of paths is especially unpleasant for moving on “bare” ground during or immediately after rain .

After the project is drawn up, you can transfer it to the territory of the site.

Marking on the ground

To determine the width and direction of the tracks, it is necessary to make markings on the ground. This is especially important if they are kept in certain sizes in width - for example, laid out from finished tiles or bricks.

Marking is carried out with the help of driven pegs and a cord pulled over them. To make it more convenient to visually figure out how the direction will look like, and whether the width of the path is sufficient, each border on the sides can be sprinkled with lime a little.

The best option is if, along with the path, you immediately mark the location of the plants that will frame it, since everything looks a little different on the ground than in the project.

At the planting sites of bushes and trees, which will be located along the path, you can install signs or lay out stones, and mark the boundaries of future flower beds with lime.

It must be remembered that the pit to be torn off should be somewhat wider than the path itself, since in order for it to serve for many years, it must be protected on both sides with stone or concrete curbs. Whatever material it is planned to build a track from, such a preparatory part will in any case improve the quality of the work and allow the laid out track to function for a long time.

After marking, you can proceed to the preparatory earthworks.

Preparing the base for the garden path

So that the path does not crumble in a year or is not overgrown with grass with the same sad outcome, serious preparatory work needs to be carried out. At the same time, it must be remembered that the path should have a slight slope in one or both directions. In addition, a small trench is made in the side of the slope, into which water will drain during rain.

• First of all, from the places where the path will pass, a fertile layer is removed, 15 ÷ 200 mm thick. In order for the depth of the pit to be approximately the same along its entire length, it is necessary to control its sides with a ruler.

• Further, in order to maintain the evenness of the edges of the future path, boards are installed inside, along the entire length of the walls of the pit, but under them it is first desirable to add and compact some sand.
• If the pit is limited by concrete curbs, then their width should be 70 ÷ 100 mm greater than the height of the walls of the pit. The curbs are set according to the level, and so that they do not move, they are fixed with reinforcing bars, which are driven into the ground inside the trench, next to the curbs. The length of the rods should be from 250 to 350 mm, and this segment should be clogged by 200 ÷ 300 mm. The pin remaining above the ground will hold the curb in the desired position.

• If the walls of the pit turned out to be uneven due to excessively loose soil, then reinforcing pins will also have to be driven into the walls, and then installed, pressing curbs against them, setting them in level and also fixing on the other hand pins.

• Further, crushed stone or gravel mixed with sand or cement is poured into the bottom of the pit. can be from 50 to 100 mm after tamping.

… and careful tamping to maximum density

• After backfilling and distribution over the pit, the resulting surface is periodically moistened and thoroughly compacted.

The type of material to be poured will largely depend on the total thickness of the “cushion”, on the type of top decorative coating. Also, do not forget that between the "cushion" and the top lining, most often a layer of sand should still be placed.

Varieties of garden paths for a suburban area

As mentioned above, paths can be made from different materials. It is worth considering the installation of some of them in order to accurately determine the choice of the most suitable option.

brick path

A fairly reliable, durable and aesthetic path is obtained from a brick. It is laid out, in principle, using the same technology as paving slabs or. In order for such a path to last for a long time, you need to choose high-quality clinker bricks and carry out work very carefully.

• The base for the path, with a compacted upper sand layer, needs to be well leveled using a homemade rule.

The rule is made from a board with perfectly even and smooth end sides. The board should have a length of 200 mm more than the width of the path. The corners of the bottom of the board are cut to the thickness of the brick. Upper, longer uncut parts boards will serve as a stop and limiter when leveling the sand layer.

• When the entire sand layer is leveled, you can proceed with the installation of side bricks in the path, which are installed on the edge and driven half the width into the sand with a rubber mallet.

Laying and driving in a line of "border" bricks

• If a curb is not provided in the path device, then the side bricks are fastened together with a mortar, and after it hardens and is removed, they must be fixed from the outside with reinforcing pins, and then a crushed stone bed should be arranged, which will need to be carefully tamped.
• After installing the side bricks on both sides of the path, you need to decide what pattern the middle of the path will be laid out with. The brick can be installed on the end or laid on its wide side.

• To make the masonry rigid, you need to lay one row along and the other across the path, driving bricks into the sand at the same level in height with the framing ones. However, to make the path as reliable as possible, it is advised to fasten the bricks together with a cement-based adhesive solution intended for outdoor work - this will also reduce the risk of grass growing in the gap between the bricks.

It is advisable to put the solution in such a way that it does not protrude from above, but remains inside the masonry, which means that it will not require too much.

• After the laying of the path is completed, the gaps between the bricks are filled with sand. To do this, he spills out onto the path and with a long-haired brush is distributed first over one area, then in another way - and so on until all the gaps are completely filled.

The remaining excess sand is swept off the surface with the same brush.

• Further, when the path is almost ready, the formwork from the boards is removed from its sides. On the outer edge of the path, crushed stone of the middle fraction is poured and carefully compacted, and another layer of crushed stone is freely poured on top of it.
• To brighten the color and prolong its service life, it is recommended to treat the brick with a penetrating primer, and after it dries, cover it with a varnish that is suitable for stone in outdoor conditions.

With some assumption, a variety of such tracks can be considered those that are made of thick ones. How the process takes place is shown in detail in the video.

Video: garden path laying master class

Round log path

Option number 1

To "paving" the path with columns, you need to take a dried tree of one of the hard species. Round logs should have a flat surface, so they must be cut very carefully.

Then the surface of the stumps is cleaned and leveled.

• For the construction of the path, logs of different diameters are taken, so that it turns out to fill the space of the pit as densely as possible.

The height of the round timber should be twice the height of the walls of the pit, counting from the compacted gravel, that is, the columns should rise above the surface of the soil located around the future path by 100 ÷ 130 mm.

• When the log blanks are prepared, it is necessary to treat their lower part with an antiseptic that will protect the wood from biological pests and the negative impact of ground moisture on it.

This is best done by placing the stumps in turn in a container with liquid and leaving for 3 ÷ 4 minutes. The rest of the surface is simply applied with a wide brush. Before installing the paths in the pit, the round timber is thoroughly dried.

• After drying, the hemp is dipped into the "Kuzbass varnish" for a few seconds - it will perfectly protect the wood from moisture. However, the disadvantage of this composition is that its structure is destroyed by exposure ultraviolet rays and overheating. However, if it processes only the lower part of the stumps, which will be closed by the wall of the pit, sand, geotextiles and gravel, then such detrimental effects do not threaten.

A regular heated tar can serve as a substitute for varnish, which, when cooled, forms a fairly dense film on the surface of the stumps - it is not afraid of either high temperature or sunlight.

• Prepared round timber from trunks of different diameters begin to install on the rammed at the bottom gravel pit as follows:

- A small amount of sand is poured to the transverse wall of the pit at the beginning of the path.

- Then, the first row of round timber is installed. It must be well sized so that it fits as tightly as possible.

- Sand is poured between the logs to the level of the top of the walls of the pit.

“Such cyclical manipulations continue until the end of the path.

• Along the edge of the path, a sandy border is filled up and compacted.

Option number 2

Another option using round stumps, which is arranged in combination with crushed stone or gravel.

In this case, only the curb is mounted from the stumps, and the remaining stages of work with the removal of soil, the embankment of sand and the installation of stumps to the walls of the pit are carried out in the same way as a path completely made of logs. The process goes in the following sequence:

• At the bottom of the pit, a "cushion" of sand is poured and rammed;
• Then, along the edge of the future path, stumps are installed, which are driven into one level and sprinkled with sand. Sand bedding is compacted directly near the bottom of the stumps;
• After the borders of the logs are completely laid out, geotextiles are laid on the entire surface of the track, the edges whom bend on stumps by 80 ÷ 100 mm;

• The next step is an embankment of gravel or medium fraction crushed stone directly on geotextiles;

A mound of gravel is distributed over the entire area of ​​\u200b\u200bthe track in an even layer. If necessary, the layer is increased, since it must be equal in height to the level of the soil of the entire area.

The gravel layer should become the second retaining wall for the stumps in the curb.

• If the top of the stumps have a different color, but you want to achieve harmony in the design of the track, then they can be covered with paint intended for external work, and the shade in this case is selected to the taste of the owner of the site.

Path made of round river stone

For those who value originality - a mosaic path made of river stone

Paths with amazing curls are obtained from Altai river stone, which has bluish hues, from very light to dark blue-gray. To make such a wonderful track, you need to prepare round and oval smooth stones of different sizes, clean sand, a rubber or wooden mallet, cement, a sponge, a level, and, of course, water.

The preparatory work takes place in almost the same way as with the construction of a brick path, but with slight deviations.

The whole process begins with the sorting of stones, as they come with a small marriage. If the flaw is not too large, then it can be hidden by turning the stone straight side up.

After going through the stones, you need to choose a pattern that is suitable in size to the width of the track, the base for which has already been prepared. If a suitable one was not found, then it can be easily compiled on your own, using squares as a basis for drawing, into which curls-shells will fit perfectly.

Option number 1

• The drawing from the sketch is transferred to the prepared base. The curl must be placed in the marked square, and it is desirable that this square has from all four sides of the sides, which prevent the mosaic from falling apart.

Since the base is made of crushed stone, the markup can be done with lime.

• The next step is to mix sand with cement, approximately 3:1 or 4:1, add water and make a thick mixture, from which a side is laid out according to the marking, having a width equal to the length of the pebbles. The strips are arranged in small sections to make it easier to equalize the stones in them.
• An oval stone with rounded edges is folded into a small path - it is laid on the side and slightly pressed into the solution.

If the solution has already hardened a little, then to align all the stones, you can tap on them with a rubber mallet.

• When one of the strips is laid out, its evenness must be checked using the building level - there should not be strong protrusions above the general level of the track.

• So, looking at your sketch, row after row, they lay out a similar stone mosaic. It can be used as small oval smooth stones, with their installation on the edge, and round, if they fit well into the pattern being created.

• In addition, you can use different shades of stones, for example, laying out one stripe with light stones, the other with dark ones, or making a smooth color transition.
• Depending on the conceived pattern, the stones can be installed in height. The main thing is to keep constant control with the help of the level.

• After one of the parts of the mosaic is laid out, it is watered with a spray bottle. This will not only strengthen the curing mortar, but also wash away its excess from the surface of the mosaic.

• So, dividing the drawing into separate parts, gradually, in accordance with the sequence thought out in advance, lay out the entire plane reserved for the mosaic. As a result, it should be densely filled with stones.

Option number 2

Another option can be called simpler, since the stones are immediately laid in leveled wet sand, without the use of cement.

However, so that the created composition does not crumble ahead of time, it must be laid out in a limited space. For this, installed borders with temporary partitions can serve, since the mosaic is laid out in parts, or a kind of formwork made of boards, which is removed only after compaction of each of the parts.

• So, curbs, as well as temporary partitions, which will limit the area of ​​work being carried out, are set up and leveled on a base with compacted gravel.
• Further, wet sand is poured into the resulting form, compacted and leveled with a rule. The height of the sand cushion should be 20 ÷ 30 mm lower than the sides of the curb or formwork - it is at this height that the stones will remain on the surface, and the laid mosaic will need to be aligned along the curb.

Lines are drawn on the leveled sandy surface along which the stone mosaic will be laid out.

• It is more convenient to lay out the stones not one at a time, but immediately fold them into a path and, tapping on top with a rubber mallet, deepen to the desired level. If necessary, the sand must be additionally moistened.

When carrying out work, the height of the stones must be constantly monitored using.

• Having laid out a certain section of the mosaic, until the sand has dried, you need to once again walk over the entire surface with a rubber mallet, and then you need to pour more dry sand or a mixture of sand and cement on top. The excess of such backfill must then be immediately brushed off.

• After complete drying of the laid surface, you can once again walk over the surface with a brush.

After a few hours, the sand will compact and sink a little between the stones. After that, you need to repeat the procedure with backfilling and splashing.

• After the next drying of the mosaic, all the stones are washed with a wet sponge.

• The entire composition is wetted with water every day, for a week - this is necessary in order for the track to “gain rigidity”.
• If a work in progress for the installation of mosaics in open space, then in order to avoid blurring it with rain, at night it is best to cover the entire composition with thin foam rubber. It will allow water to pass through, but will not allow sand to be washed out.
• If the work was carried out in the formwork from the boards, after the completion of the masonry and its temporary fencing, it is necessary to strengthen the path by lining it with stones or bricks in the form of a curb.

concrete walkway

For a concrete path, marking is carried out in the same way as described above, and then excavation is carried out along the marked area.

Then, sand is poured to the bottom of the pit, which is moistened and compacted. The final thickness of the compacted layer should be 60 ÷ 70 mm.

Crushed stone is poured on top of the compacted sand, which also needs to be compacted.

A reinforcing grate is installed on the rubble, which will make the path much stronger.

Then, you can do one of two ways, depending on which track you want to get.

1. If a flat surface should be obtained, then a thin one is made, with which the formwork is poured.

- In the case when concrete is poured into the space between already installed curbs, then the rule will need to be made independently, and it must have the same basic form as the one described in the section on sand leveling when constructing a brick path.

- The finished track is reinforced with iron. To do this, dry cement is scattered on a still wet surface with a thin layer, which is immediately gently rubbed with a grout. You can also use commercially available hardening topping mixtures.

2. If the path is planned to be made using a form that helps to imitate stone laying, then the concrete mixture is poured into the formwork in two layers.

- The first layer is poured to half the height of the formwork and leveled also using the rule. In this case, a coarse mortar is used, consisting of cement and gravel. The surface should turn out to be fairly even, and in order to achieve this, it is recommended to install beacons of the desired height, and equalize the concrete along them.

- After the concrete has set, a mold is set on its surface and filled with a thin mortar. It aligns with the surface of the form. The form poured with concrete is left to harden for 3 ÷ 5 days.

Figured shapes for a "paved path" effect

If there is only one form, then the work, of course, will be carried out for too long, therefore, when using such a technology, it is desirable to have at least two similar forms at your disposal. It should be noted that with their help you can arrange not only paths, but also the floor in the gazebo, the area near the gate or near the garage.

Video: an example of using a form to fill a "paved" track

Cover garden paths

A very interesting version of the track - it turns out that it can be made from caps from ordinary plastic bottles. Thanks to their bright, varied colors, they can be used to make various ornamental patterns that will help decorate the landscape of the garden.

The only difficulty that will be encountered on the way of the master who decides to make this work will be the collection of the required number of these "mosaic elements" of the future track.

Having decided to do this work, you need to start collecting covers in advance. While the process with boron is going on, you can think about which pattern to choose for the track and draw up a rough sketch of it.

You should not wait until the required number of covers for the entire length of the path is fully assembled. Having collected a certain number of them, you can begin to mount elements of the future canvas from them. For example, to assemble the fragment shown in the photo, you will need only 19 covers.

A large number of covers are usually found in the summer on the beach. And by the way, you can get three benefits from the collection process:

- at least a little to clean the sand of the beach from foreign objects;

- breathe fresh air while walking along the beach;

- get completely free material for the manufacture of the track.

• To connect the covers in the desired pattern, you will need a “gypsy” needle, an awl, always with a wooden handle, and a large amount of fishing line. A wooden handle is needed due to the fact that the awl will have to be heated on fire so that holes can be easily made in the lids for fastening them together.
• Holes for the passage of the needle are pierced from the sides of the covers, as shown in the photo above.
• First, individual elements are assembled, according to the prepared sketch. , and when several of them are ready, they are interconnected.
• The work on assembling the elements of such a track is quite long and painstaking, but it does not require t ore-intensive preparation of the base associated with earthworks or concrete work.

In the presence of material and the necessary diligence and patience, it is possible to “pave” quite large areas

• When the rug from the covers is completely ready, the place for it is prepared as follows:

- marked space for installation, spilled with weed control;

- then, a prepared mat of covers is laid on it;

- so that less soil gets on the surface of the track during operation, it is recommended to install a border of brick or stone along the track;

- for this, the upper soil is removed to a depth of about two-thirds of the brick, and then the space of the trench is half filled with sand, into which the brick is set at a corner and the brick is tapped. The side gaps between the soil and the brick are also filled with sand, which is moistened in advance.

Prefabricated paths made of plastic plates

Mobile garden paths can be laid quickly, without arranging a foundation for them, using special plastic panels.

From them you can assemble a path of any width, as they have fasteners that will allow you to connect them both along and across.

The connecting elements, which are large enough, give the structure rigidity, since every two plates are fastened in two places and serve as a kind of stand-legs.

The advantage of such slabs-panels is not only the speed of installation, but also the fact that their surface is absolutely non-slippery, such tracks can withstand quite large loads, they are very durable in operation.

For the manufacture of plates, frost-resistant plastic is used, which well withstands not only low temperatures up to - 35 ÷ 40, but also high temperatures up to + 45 ÷ 50 degrees. However, leaving such a garden path for the winter does not make much sense - if desired, it can be quickly and easily disassembled, stacked and sent for storage to one of the outbuildings. The tile will not take up much space, and in the spring, the path will not be ore in the shortest possible time to lay it out again anywhere on the site.

The tile has a very convenient size for working with it - it is 570 × 570 mm wide and 570 mm long, and its thickness is 22 mm.

In addition, the convenience of such a tile also lies in the fact that water does not accumulate on it, since there are longitudinal holes on the surface.

By the way, for the winter period, you can lay out a rug from such a tile in front of the front door - its surface is corrugated, which means it will not allow you to slip and get injured.

This option for arranging garden paths does not require much effort for installation, since tiles can be laid both on and on the soil surface. If grass begins to grow through the holes in the tile, the path can be easily moved or disassembled, and after getting rid of the grass, collect it and put it back in place.

"Garden parquet"

"Garden parquet" - quite expensive the type of material that they are used not only for laying on the site, but also for decorating floors in gazebos, on verandas, terraces and balconies.

Expensive, but very cool - "garden parquet"

It has characteristics similar to plastic plates. This option is great for laying on garden paths- “garden parquet” is also quickly assembled and disassembled, as it has special fasteners for this, which have their own specific features.

Fastening tiles "garden parquet"

Detailed panels can have a different arrangement of the elements that make up its drawing. They are laid on a compacted gravel mixture or fine crushed stone.

Laying "garden parquet" will never take long

Such a “parquet” is made from wood treated in a special way and does not react to the usual external “irritants” - it is not afraid of humidity, direct sunlight, temperature changes, biological effects. However, in addition to wood, for the manufacture of "garden parquet" (relatively inexpensive models), special plastic is used, which perfectly imitates natural wood. It is clear that the second version of the parquet tile is much more accessible to the average owner of the site.

So, there is a very large number of suburban paths. After careful consideration, you can always choose the right one for the price, design and complexity of doing all the work yourself. Therefore, if the time comes for planning a site, you need to carefully consider all the nuances and calculate your strengths and capabilities.

Video: A variety of options for garden paths